Teltonika RUT976 RedCap 5G Router

The RUT976 is an industrial Redcap 5G router supporting SA architecture, carving a balanced niche between traditional 4G and full-capacity 5G. This 5G router can wirelessly support up to 100 end devices and features the low latency of 5G—at affordable pricing. In case of limited 5G coverage, the RUT976 is backward compatible with 4G LTE Cat 4. It also boasts dual SIM slots with auto-failover, Wi-Fi, GNSS, a wide range of interfaces, including four 10/100 RJ45 slots, RS232, RS485, and multiple I/Os, and numerous other brilliant features for expert professional deploymentREDCAP 5G – Low latency, high capacity, affordable pricingFUTURE-PROOFING – Backward compatible with 4G LTE Cat 4DUAL-SIM – With auto-failover, backup WAN and other switching scenariosMULTIPLE INTERFACES – Ethernet, RS232, RS485, & multiple I/OsSpecificationMobileMobile module5G Sub-6Ghz SA 223 Mbps DL , 123 Mbps UL; 4G LTE Cat 4 – LTE 195 Mbps DL, 105 Mbps UL3GPP ReleaseRelease 17 RedCapSIM switch2 SIM cards, auto-switch cases: weak signal, data limit, SMS limit, roaming, no network, network denied, data connection fail, SIM idle protectionStatusIMSI, ICCID, operator, operator state, data connection state, network type, bandwidth, connected band, signal strength (RSSI), SINR, RSRP, RSRQ, EC/IO, RSCP, data sent/received, LAC, TAC, cell ID, ARFCN, UARFCN, EARFCN, MCC, and MNCSMSSMS status, SMS configuration, send/read SMS via HTTP POST/GET, EMAIL to SMS, SMS to EMAIL, SMS to HTTP, SMS to SMS, scheduled SMS, SMS autoreply, SMPPUSSDSupports sending and reading Unstructured Supplementary Service Data messagesBlack/White listOperator black/white list (by country or separate operators)Multiple PDNPossibility to use different PDNs for multiple network access and servicesBand managementBand lock, Used band status displaySIM idle protection serviceWhen working with devices with two SIM slots, the one not currently in use will remain idle until the device switches to it, meaning that no data is used on the card until thenSIM PIN code managementSIM PIN code management enables setting, changing, or disabling the SIM card’s PINAPNAuto APNBridgeDirect connection (bridge) between mobile ISP and device on LANPassthroughRouter assigns its mobile WAN IP address to another device on LANWirelessWireless mode802.11b/g/n (Wi-Fi 4), Access Point (AP), Station (STA)Wi-Fi securityWPA2-Enterprise: PEAP, WPA2-PSK, WPA-EAP, WPA-PSK, WPA3-SAE, WPA3-EAP, OWE; AES-CCMP, TKIP, Auto-cipher modes, client separation, EAP-TLS with PKCS#12 certificates, disable auto-reconnect, 802.11w Protected Management Frames (PMF)SSID/ESSIDSSID stealth mode and access control based on MAC addressWi-Fi usersUp to 100 simultaneous connectionsWireless Connectivity FeaturesWireless mesh (802.11s), fast roaming (802.11r), BSS transition management (802.11v), radio resource measurement (802.11k)Wireless MAC filterAllowlist, blocklistWireless QR code generatorOnce scanned, a user will automatically enter your network without needing to input login informationTravelMateForward Wi-Fi hotspot landing page to a subsequent connected deviceEthernetWAN1 x WAN port 10/100 Mbps, compliance IEEE 802.3, IEEE 802.3u, 802.3az standards, supports auto MDI/MDIXLAN3 x LAN ports, 10/100 Mbps, compliance IEEE 802.3, IEEE 802.3u standards, supports auto MDI/MDIXNetworkRoutingStatic routing, Dynamic routing (BGP, OSPF v2, RIP v1/v2, EIGRP, NHRP), Policy based routingNetwork protocolsTCP, UDP, IPv4, IPv6, ICMP, NTP, DNS, HTTP, HTTPS, SFTP, FTP, SMTP, SSL v3, TLS, ARP, VRRP, PPP, PPPoE, UPNP, SSH, DHCP, Telnet, SMPP, SNMP, MQTT, Wake on Lan (WOL), VXLANVoIP passthrough supportH.323 and SIP-alg protocol NAT helpers, allowing proper routing of VoIP packetsConnection monitoringPing Reboot, Wget Reboot, Periodic Reboot, LCP and ICMP for link inspectionFirewallPort forward, traffic rules, custom rulesFirewall status pageView all your Firewall statistics, rules, and rule countersPorts managementView device ports, enable and disable each of them, turn auto-configuration on or off, change their transmission speed, and so onNetwork topologyVisual representation of your network, showing which devices are connected to which other devicesDHCPStatic and dynamic IP allocation, DHCP relay, DHCP server configuration, status, static leases: MAC with wildcardsQoS / Smart Queue Management (SQM)Traffic priority queuing by source/destination, service, protocol or port, WMM, 802.11eDDNSSupported >25 service providers, others can be configured manuallyDNS over HTTPSDNS over HTTPS proxy enables secure DNS resolution by routing DNS queries over HTTPSNetwork backupWi-Fi WAN, Mobile, VRRP, Wired options, each of which can be used as an automatic FailoverLoad balancingBalance Internet traffic over multiple WAN connectionsHotspotCaptive portal (hotspot), internal/external Radius server, Radius MAC authentication, SMS authorisation, SSO authentication, internal/external landing page, walled garden, user scripts, URL parameters, user groups, individual user or group limitations, user management, 9 default customisable themes and optionality to upload and download customised hotspot themesSSHFSPossibility to mount remote file system via SSH protocolPort MirroringMirroring network traffic on Ethernet ports for monitoring and analysisSecurityAuthenticationPre-shared key, digital certificates, X.509 certificates, TACACS , Internal & External RADIUS users authentication, IP & login attempts block, time-based login blocking, built-in random password generatorFirewallPreconfigured firewall rules can be enabled via WebUI, unlimited firewall configuration via CLI, DMZ, NAT, NAT-T, NAT64Attack preventionDDOS prevention (SYN flood protection, SSH attack prevention, HTTP/HTTPS attack prevention), port scan prevention (SYN-FIN, SYN-RST, X-mas, NULL flags, FIN scan attacks)VLANPort and tag-based VLAN separationMobile quota controlMobile data limit, customizable period, start time, warning limit, phone numberWEB filterBlacklist for blocking out unwanted websites, Whitelist for specifying allowed sites onlyAccess controlFlexible access control of SSH, Web interface, CLI and TelnetSSL certificate generationLet’s Encrypt and SCEP certificate generation methods802.1xPort-based network access control serverVPNOpenVPNMultiple clients and a server can run simultaneously, 27 encryption methodsOpenVPN EncryptionDES-CBC 64, RC2-CBC 128, DES-EDE-CBC 128, DES-EDE3-CBC 192, DESX-CBC 192,BF-CBC 128, RC2-40-CBC 40, CAST5-CBC 128, RC2-64-CBC 64, AES-128-CBC 128, AES-128-CFB 128, AES-128-CFB1 128, AES-128-CFB8 128, AES-128-OFB 128, AES-128-GCM 128, AES-192-CFB 192, AES-192-CFB1 192, AES-192-CFB8 192, AES-192-OFB 192, AES-192-CBC 192, AES-192-GCM 192, AES-256-GCM 256, AES-256-CFB 256, AES-256-CFB1 256, AES-256-CFB8 256, AES-256-OFB 256, AES-256-CBC 256IPsecXFRM, IKEv1, IKEv2, with 14 encryption methods for IPsec (3DES, DES, AES128, AES192, AES256, AES128GCM8, AES192GCM8, AES256GCM8, AES128GCM12, AES192GCM12, AES256GCM12, AES128GCM16, AES192GCM16, AES256GCM16)GREGRE tunnel, GRE tunnel over IPsec supportPPTP, L2TPClient/Server instances can run simultaneously, L2TPv3, L2TP over IPsec supportStunnelProxy designed to add TLS encryption functionality to existing clients and servers without any changes in the program’s codeDMVPNMethod of building scalable IPsec VPNs, Phase 2 and Phase 3 and Dual Hub supportSSTPSSTP client instance supportZeroTierZeroTier VPN client supportWireGuardWireGuard VPN client and server supportTincTinc offers encryption, authentication and compression in it’s tunnels. Client and server support.BACNETSupported modesRouterSupported connection typesRS485, TCPConfiguration optionsSupport for multiple BACnet/IP interfaces, Network number assignment, Preconfigured BDT entries for BBMD (BACnet Broadcast Management Device)OPC UASupported modesClient, ServerSupported connection typesTCPMODBUSSupported modesServer, ClientSupported connection typesRTU (RS232, RS485), TCP, USBCustom registersMODBUS TCP custom register block requests, which read/write to a file inside the router, and can be used to extend MODBUS TCP Client functionalitySupported data formats8-bit: INT, UINT; 16-bit: INT, UINT (MSB or LSB first); 32-bit: float, INT, UINT (ABCD (big-endian), DCBA (little-endian), CDAB, BADC), HEX, ASCIIDATA TO SERVERProtocolHTTP(S), MQTT, Azure MQTT, KinesisData to serverExtract parameters from multiple sources and different protocols, and send them all to a single server; Custom LUA scripting, allowing scripts to utilize the router’s Data to server featureMQTT GatewayModbus MQTT GatewayAllows sending commands and receiving data from MODBUS Server through MQTT brokerDNP3Supported modesTCP Master, DNP3 OutstationSupported connection typesRS232, RS485, TCP, USBDLMSDLMS SupportDLMS – standard protocol for utility meter data exchangeSupported modesClientSupported connection typesRS232, RS485, TCPCOSEMAllows to scan meter COSEM objects for automatic detection and configurationAPITeltonika Networks Web API (beta) supportExpand your device’s possibilities by using a set of configurable API endpoints to retrieve or change data. For more information, please refer to this documentation: https://developers.teltonika-networks.comMonitoring & ManagementWEB UIHTTP/HTTPS, status, configuration, FW update, CLI, troubleshoot, multiple event log servers, firmware update availability notifications, event log, system log, kernel log, Internet statusFOTAFirmware update from server, automatic notificationSSHSSH (v1, v2)SMSSMS status, SMS configuration, send/read SMS via HTTP POST/GETCallReboot, Status, Mobile data on/off, Output on/off, answer/hang-up with a timer, Wi-Fi on/offEmailReceive email message status alerts of various servicesTR-069OpenACS, EasyCwmp, ACSLite, tGem, LibreACS, GenieACS, FreeACS, LibCWMP, Friendly tech, AVSystemMQTTMQTT Broker, MQTT publisherSNMPSNMP (v1, v2, v3), SNMP Trap, Brute force protectionJSON-RPCManagement API over HTTP/HTTPSRMSTeltonika Remote Management System (RMS)IoT PlatformsThingWorxAllows monitoring of: WAN Type, WAN IP, Mobile Operator Name, Mobile Signal Strength, Mobile Network TypeCumulocity – Cloud of ThingsAllows monitoring of: Device Model, Revision and Serial Number, WAN Type and IP, Mobile Cell ID, ICCID, IMEI, Connection Type, Operator, Signal Strength. Has reboot and firmware upgrade actionsAzure IoT HubCan be configured with Data to Server to send all the available parameters to the cloud. Has Direct method support which allows to execute RutOS API calls on the IoT Hub. Also has Plug and Play integration with Device Provisioning Service that allows zero-touch device provisioning to IoT HubsAWS IoT CoreUtility to interact with the AWS cloud platform. Jobs Support: Call the device’s API using AWS Jobs functionalitySystem CharacteristicsCPUMediatek, 580 MHz, MIPS 24KEcRAM128 MB, DDR2FLASH storage16 MB, NOR FlashFirmware / ConfigurationWEB UIUpdate FW from file, check FW on server, configuration profiles, configuration backupFOTAUpdate FWRMSUpdate FW/configuration for multiple devices at onceKeep settingsUpdate FW without losing current configurationFactory settings resetA full factory reset restores all system settings, including the IP address, PIN, and user data to the default manufacturer’s configurationFIRMWARE CUSTOMISATIONOperating systemRutOS (OpenWrt based Linux OS)Supported languagesBusybox shell, Lua, C, C Development toolsSDK package with build environment providedGPL customizationYou can create your own custom, branded firmware and web page application by changing colours, logos, and other elements in our firmware to fit your or your clients’ needsPackage ManagerThe Package Manager is a service used to install additional software on the deviceLocation TrackingGNSSGPS, GLONASS, BeiDou, Galileo and QZSSCoordinatesGNSS coordinates via WebUI, SMS, TAVL, RMSNMEANMEA 0183NTRIPNTRIP protocol (Networked Transport of RTCM via Internet Protocol)Server softwareSupported server software TAVL, RMSGeofencingConfigurable multiple geofence zonesSerialRS232DB9 connector, RS232 (with RTS, CTS flow control)RS485RS485 Full Duplex (4 wires) and Half Duplex (2 wires). 300-115200 baud rateSerial functionsConsole, Serial over IP, Modem, MODBUS gateway, NTRIP ClientUSBData rateUSB 2.0ApplicationsSamba share, USB-to-serialExternal devicesPossibility to connect external HDD, flash drive, printer, USB-serial adapterStorage formatsFAT, FAT32, exFAT, NTFS (read-only), ext2, ext3, ext4Input / OutputInput1 x digital dry input (0 – 3 V), 1 x digital galvanically isolated input (0 – 30 V), 1 x analog input (0 – 24 V), 1 x Digital non-isolated input (on 4-pin power connector, 0 – 5 V detected as logic low, 8 – 30 V detected as logic high)Output1 x digital open collector output (30 V, 250 mA), 1 x SPST relay output (40 V, 4 A), 1 x Digital open collector output (30 V, 300 mA, on 4-pin power connector)EventsEmail, RMS, SMSI/O jugglerAllows to set certain I/O conditions to initiate eventPowerConnector4-pin industrial DC power socketInput voltage range9 – 30 VDC, reverse polarity protection; surge protection >31 VDC 10us maxPoE-out input voltage range44 – 57 VDCPoE (passive)Passive PoE over Port LAN1. “Mode A/B” style. Not compatible with 802.3af/at/bt.Passive PoE over spare pairs. Possibility to power up through LAN port, not compatible with IEEE802.3af, 802.3at and 802.3bt standards, Mode B, LAN1 Port, 9 – 30 VDCPower consumptionIdle: < 3 W, Max: < 7 WPhysical InterfacesEthernet4 x RJ45 ports, 10/100 MbpsI/O’s2 x Inputs and 2 x Outputs on 10-pin industrial socket, 1 x Digital input and 1 x Digital output on 4-pin power connectorStatus LEDs1 x Bi-color connection status, 5 x Mobile connection strength, 4 x ETH status, 1 x PowerSIM2 x SIM slots (Mini SIM – 2FF), 1.8 V/3 V, external SIM holders, eSIM (Optional – different hardware required; contact your sales manager)Power1 x 4-pin power connectorInput/output1 x 10-pin industrial socket for inputs/outputsAntennas2 x SMA for Mobile, 3 x RP-SMA for Wi-Fi, 1 x SMA for GNSSUSB1 x USB A port for external devicesRS2321 x DB9 socketRS4851 x 6-pin industrial socketResetReboot/User default reset/Factory reset buttonPhysical SpecificationCasing materialAluminum housing, plastic panelsDimensions (W x H x D)110 x 50 x 100 mmWeight295 gMounting optionsDIN rail, wall mount, flat surface (all require additional kit)Operating EnvironmentOperating temperature-40 °C to 75 °COperating humidity10% to 90% non-condensingIngress Protection RatingIP30Regulatory & Type ApprovalsRegulatoryWEEE SKU: TELTONIKA-RUT976-N Categories: 5G Routers, Teltonika, Teltonika 5G Routers Tags: 5G IOT Router, 5G redcap router, Cellular Router, dual sim 5g router, Edge Networking, fixed ip router, industrial 5g router, Industrial Automation, Industrial Connectivity, iot router, M2M router, Machine to Machine Communication, Private APN Router, Reliable 5G Router, Remote Access Router, Remote Monitoring, Secure IoT Connectivity, Teltonika Networks, Teltonika RUT976, UK 5G Router Brand: Teltonika